OptiWand 3 Pack Soft Contact Lens Insertion Removal Tool. Eye Lens Inserter

Description

This listing is for a box of 3 OptiWand's.
OptiWand is made of SOFT PLIABLE RUBBER &
Is a Soft Contact Lens Insertion & Removal Tool
It can be used to INSERT ALL CONTACT LENSES.
It WILL remove soft contact lenses with some practice & patience by PINCHING THEM WITH THE SOFT ENDS!
****************
IT IS NOT A SUCTION CUP FOR SOFT LENSES
We strongly recommend starting with insertion as it should be easier to perfect
Removal's pinch can be tricky but once mastered it is super simple
Practice and patience are a must and old habits must be broken in order to use it properly
Soft contact lenses are NOT a SOLID material and CANNOT be grabbed by placing the OptiWand against them
You must break the bond between contact lens & your CORNEA where your lenses sit securely as designed
IT WILL NOT Remove RGP/Hard/Sclera lenses
The Split Cup side will insert Sclera lenses and either side will insert RGP
*It has an EMERGENCY BLINK RELEASE TO PREVENT STICKING TO NAKED EYE *
For proper insertion you must focus on the CENTER HOLE and not a mirror or other source.
The soft contact LENS WILL NOT come off the OptiWand unless it is placed properly directly on the cornea.
If you are bringing it in at an angle the contact lens will stay on the OptiWand and not come off on to the eye as intended.
Using
OptiWand
for inserting SOFT & HARD Contact Lenses
Step 1: Dip your
OptiWand
in Contact Lens solution for lubrication
Step 2: Position your regular sized HARD or SOFT contact lens on the center of FULL CUP SIDE of the
OptiWand
.  If you have small soft eyes or hard lenses you can use the SPLIT CUP end and use the following steps.  The OptiWand is designed to hold the lens during insertion
.
Step 3: Using your non-dominant hand spread your eye lids as wide as possible,
keeping your eyelashes out of the way.
Step 4: Draw the
OptiWand
to your eye by looking DIRECTLY AT THE LENS through the
CENTER HOLE to align properly.
*Aiming the OptiWand at a colored background or light will help some to focus on the CENTER HOLE*
Step 5:
Once it is close enough and the contact lens touches your eye, give
the OptiWand a slight TWIST to help release the lens.
Step 6:  Blink your contact into place.
Now your lens is centered on your eye.
* Make sure to hold eyelashes away to prevent blockage. *
WARNING **NEVER USE
OptiWand
ON NAKED EYE**
Please DO NOT USE the OptiWand if you are allergic to Liquid Silicone Rubber!
Using
OptiWand
for Removing SOFT Contact Lenses
YOU CAN USE THE FULL CUP OR SPLIT CUP TO PINCH SOFT LENSES.
SPLIT CUP END IS BEST IF YOU HAVE SMALL EYES OR LENSES.
FULL CUP END IS BEST FOR LARGER FINGERS OR LONG FINGERNAILS.
Step 1: Use a DRY
OptiWand
for Soft Contact Lens removal for best results.
Step 2: Using your non-dominant hand spread your eye lids as wide as possible,
keeping your eyelashes out of the way.
Step 3: Focusing through the CENTER HOLE, draw the
OptiWand
t
o your eye until you touch the soft contact lens.
Step 4: Once you feel the
OptiWand
touch the soft contact lens you should twist it slightly then carefully pinch the soft contact lens with the Base of the
OptiWand
and swipe away from eye.  Some users can turn the OptiWand towards their noses after it makes contact and that will help push it out.
*Best pinching position is very close to the tip*
Final Step: Dip
OptiWand
into contact lens solution in current case and the lens will fall down into the solution with a pinch on the Full cup.
We suggest placing the soft lens on your non dominant index finger and PRACTICE THE PINCH OFF OF YOUR FINGER to get a feel for actual removal.
If you pinch the soft contact lens off of a finger a few times you will be able to visualize what it takes to pinch effectively.
Using
OptiWand
for inserting Large Sclera contact lenses
Step 1: Dip your
OptiWand
SPLIT CUP SIDE in Contact Lens solution for lubrication
Step 2: Stand the OptiWand up on the counter or table top with the Split cup side up
Step 3: Position your Sclera contact lens on the center of the SPLIT CUP SIDE of the
OptiWand
Step 4: Look & stay focused on the CENTER HOLE for proper alignment.
* Some prefer to have a colored background to help focus on the CENTER HOLE *
Step 5:  Spread your eye lids as wide as possible, keeping your eyelashes out of the way.
Step 6:  Slowly draw to the OptiWand until the contact lens makes contact with the eye.
Step 7:  Blink until comfortable
USE ONLY AS DIRECTED
Please read and follow instructions as well as view the instructional videos for best results.
Please DO NOT USE the OptiWand™ if you are allergic to Liquid Silicone Rubber.
Warning Small Parts Choking Hazard! Not suitable for children under 5 years old.
OptiWand™, OptiCase™ & OptiAide are disposable products.
We suggest replacing after 30 Days with daily use.
To clean use soft soap, rinse thoroughly and air dry.  Not dishwasher tested.
These statements have not been evaluated by the Food and Drug Administration.
This product is not intended to diagnose, treat, cure, or prevent any disease.
If you are unhappy with your OptiWand™, OptiCase™ or OptiAide
you will be given a refund, less a 10% restocking fee
OptiWand™ & OptiCase™ are registered trademarks of TJSC Optix Inc. All rights reserved
Patent No. Des. D791,858S
Patent No. Des. D806,387S