Buffing Compound Hard Metal Polishing Cut & Polish White Color Alloy Metals 2Bar

Description

WHITE
LUSTER
-
GREY STAR
CUTTING & POLISHING COMPOUND
BUFFING COMPOUNDS FOR WHITE ALLOY METALS
-
METAL BUFFING MATERIAL
CUT & POLISH
-
Sale is for a
bar each
of the
Cutting Compound
GREY STAR
and
Polishing and
Finishing Compound
WHITE
LUSTER
.
Grey Star
Polishing Compound is primarily a cutting compound that has been widely used for lapping and pre-polishing.  This compound is used by polishers on metals to cut and bring out the color of the material.
The Gray Star compound works well on Precious and Ferrous metals has an excellent capacity to bring out good color of all metals. A BIG plus on this formulation is that it’s a Water Soluble Compound.
Polishing Compounds used in lapping application are used with buffs and felt wheels.
The Graystar has a medium grade composition with fine and uniform abrasives that provide its cutting ability.
It is an exceptional buffing compound material for polishing a wide range of metals, in particular for use on white/grey color metals and even harder metals. Works well on Precious metals as well as non-precious:  Platinum, Stainless Steel, and Palladium polishing.
White Luster
Buffing
Compound provides a High Luster finish on all types of metals from precious and decorative metals. Its formulation removes light scratches and produces a fast and bright final luster. A particular quality of the White Luster is that the final finish has no discoloration. It is a grease-less and dry compound leaving very little residue for fast and easy clean up. The White Luster is a very popular compound with Jewelry Manufacturers in the US.
Compound works on and can be used with a wide range of metals, it is an exceptionally well with soft metals. It can be used on a wide range of metals is excellent for Aluminum, Silver, Brass, and very good finish alloy wheels.
NOTE:
We have included polishing recommendations at the bottom of this page, to assist you.
SPECIFICATIONS OF COMPOUNDS
WHITE
LUSTER
COMPOUND
JETS Product #1614-052
Made in USA
Bars Size:
6" x 2" x 1-3/4"
-
150mm x 53mm x 32mm
Bar Weight:
Varies from
1.2oz. +/-
·
Utilizes Quality Grade Abrasives
·
Combined with Additives
·
Long Lasting Composition with Minimum Usage
·
Good Adhesion to Buffing Wheels
·
Water Soluble
·
Minimal Residue
·
No Discoloration
·
Produces
-  High Shine
.
GREY STAR
COMPOUND
JETS Product #1614-702
Made in USA
Bars Size:
6" x 2" x 1-3/4"
-
150mm x 53mm x 32mm
Bar Weight:
Approximately 1.3 Lb. / 545gr +/-
Varies from
16-18oz.
·
Utilizes Quality Grade Abrasives
·
Combined with Additives
·
Long Lasting Composition with Minimum Usage
·
Good Adhesion to Buffing Wheels
·
Water Soluble
·
Minimal Residue
·
No Discoloration
·
Produces - Clean Bright Surface
SALE
is for 2 BARS
(1 of each type)
Bars are rectangular; weights will vary on each bar. Made in USA
NOTE: Visit
JETS INC.
our ebay Store Listings, where you can see the full variety of Polishing Compounds, Buffs and Buffing Wheels and a selection of
J
ewelers
E
quipment
T
ools
&
S
upplies
.
JETSINC.
FRLE  1.5Lz  113
CKP  Z
POLISHING RECOMMENDATIONS:
Our recommendations and suggestions on Buffing to obtain the best results possible:
·
Use the right compound for the metal that you are trying to polish
·
It may be needed to go through 2 or 3 steps, in polishing to get the optimum result you are looking to achieve.
·
Make sure that the parts that are being polished are smooth and clean, use the appropriate abrasive to remove lines and scratches.
·
Avoid using different compounds with the same buff, if you have to then make sure to clean and remove any hardened compound residue on the surface edge with a buff rake.
·
Segregate your buffs for the various metals, Gold, Silver, Brass … try not to use the same buff for all metals.
If you have to then make sure buffs are cleaned (dressed) with a buff rake.
·
A clean buffing wheel edge is important.
·
Allow the buff and compound to perform the work they were made and formulated for, excessive force or pressure will hurt the process.
·
Whenever you are working with Platinum never use a buff that was used for another type of metal.
WORK SAFE!
Working with rotary motors and wheels can be dangerous if proper safety procedures are not followed
.
PROTECTION -
Protect yourself, your fingers and hands, your face and eyes and use respirators
.